Injection Moulding Machine for Washing Machine Pulsators, Filters and Lint Trap Frames
Washing machine pulsators, filters and lint trap frames are made on horizontal injection moulding machines from PP copolymer, talc-filled PP and POM. Pulsator diameter, projected area and cavity count set machine size. Strong knit lines around vanes and slots matter most, since these parts turn in hot detergent water for years.
For these wetted moving parts, machine selection focuses on consistent packing of thick vane roots and clean filling of fine slots. Pratishna Engineers supplies horizontal injection moulding machines for pulsator and lint filter production and can recommend a configuration for your tools.
Moulding Pulsators and Lint Filters?
Share your pulsator and filter drawings, grade and volume per model, and Pratishna Engineers will recommend a suitable machine.
Machine Requirements for Washing Machine Pulsator and Filter Moulding
These parts are judged by wash performance and service life rather than looks. Points to check on the machine and process:
- Accurate vane profile filled without short shots
- Void-free packing at the hub and vane roots
- Strong weld lines around every lint filter slot
- Hot detergent resistance from PP copolymer grades
- Warpage control on wide talc-filled PP discs
- Secure shaft insert placement in the pulsator hub
Recommended Machine for Washing Machine Pulsators, Filters and Lint Trap Frames
Lint trap frames and filter parts are compact and suit the E Series (75-180 T) in multi-cavity tools. Pulsators grow with drum size. Larger discs with deep vanes need the C Series (140-320 T), and the biggest discs the H Series (120-350 T), keeping shot weight well within barrel capacity.
Not Sure Which Machine You Need?
Send your pulsator or lint filter drawing for a machine recommendation.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBWhite Goods & Appliances Components & Machine Guide
A guide to White Goods & Appliances components, covering washing machine tubs and panels, refrigerator liners and trays, AC louvres and grilles, fan blades, mixer bodies and appliance housings. It explains large-part moulding, cosmetic finish, flame-retardant grades, and how to match each part to a suitable machine.
Download PDFPDF · 204 KB
FAQs / Buyer Questions
Points washing machine part makers raise most often with our engineers.
Which Injection Moulding Machine Is Used to Make Washing Machine Pulsators?
Pulsator diameter decides the machine. Smaller discs and filter frames fit the E Series, while large top-load pulsators with deep vanes need the platen and shot capacity of the C or H Series.Why Does PP Copolymer Suit Pulsators and Filters?
PP copolymer resists hot detergent and keeps its impact strength as parts flex wash after wash. Talc-filled PP adds stiffness and flatness for wide discs, and POM is used for small clips and latches.How Are the Fine Slots in a Lint Filter Frame Moulded?
Each slot splits the melt, so weld lines form around it. Gate so the flow meets at thick sections, vent the cavity well and keep melt and mould temperature high enough for the fronts to knit strongly.
Is a Metal Insert Moulded Into the Pulsator Hub?
Pulsators often carry a splined metal bush in the hub to take drive torque, either moulded in or fitted later. Moulded-in bushes need a secure insert seat, steady loading and enough packing around the knurl.Can Pratishna Recommend a Machine for My Pulsator or Lint Filter?
Yes. Share drawings or samples, the grade, part weights, mould dimensions, cavity counts, any hub insert and volume per model, and Pratishna Engineers will recommend a suitable machine.Does the Machine Suit Other Laundry and Appliance Parts Too?
Yes. Machines in this range can also mould appliance knobs and bezels, door handles, water dispenser components and appliance fan housings, subject to the mould.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]