Injection Moulding Machine for Pen Stands
Pen stands are made on horizontal injection moulding machines, often in family moulds with matching desk organiser parts, from PS, SAN, ABS or PP. Machine size follows the projected area of the stand and its partner parts, and a shot large enough for the heavy base. The base matters most: solid sections sink, so it is cored out.
For a pen stand, machine selection focuses on a shot that fills the base, steady holding pressure against sink and clean filling on clear grades. Pratishna Engineers supplies horizontal injection moulding machines for pen stand production and can recommend a configuration from your stand design, mould and output.
Manufacturing Pen Stands?
Share your stand drawing or sample, the material and the other parts in the set, and Pratishna Engineers will suggest a suitable machine.
Machine Requirements for Pen Stand Moulding
Pen stands are cosmetic parts with a heavy base, so the machine has to fill and pack them cleanly. Points to check before choosing one:
- Shot weight sized for the thick base section
- Steady holding pressure to control sink on the base
- Gate placement that keeps weld lines off clear faces
- Polished mould surfaces for crystal PS and SAN
- Matched shrinkage across stand and organiser family parts
- Pocket or insert seat for an optional weight
Recommended Machine for Pen Stands
A single pen stand is a small to medium moulding, and the E Series (75-180 T) suits many stand moulds. Family moulds that carry the stand with trays and organiser parts raise the projected area and shot weight, which can move the job to the C Series (140-320 T) or H Series (120-350 T).
Not Sure Which Machine You Need?
Send your pen stand design and the full set of parts for a machine recommendation.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBStationery Components & Machine Guide
A guide to Stationery components, covering pen barrels, caps, refills, markers, rulers, sharpeners, clips, ID card holders and desk tools. It explains high-cavity hot runner moulds, clear parts, small mechanisms, and how to match each part to a suitable machine.
Download PDFPDF · 204 KB
FAQs / Buyer Questions
Questions buyers ask most when they plan pen stand production.
Which Injection Moulding Machine Is Used to Make Pen Stands?
Most single-stand moulds run on the E Series. Larger stands, multi-compartment organisers or family tools with trays may need the C or H Series, depending on total projected area and the shot the base needs.How Is Sink Avoided on a Thick Pen Stand Base?
The base is cored out to an even wall instead of being left solid, with ribs where stiffness is needed. Gate position and holding pressure are then set so the thicker areas pack before the gate freezes.Can Clear or Tinted Pen Stands Be Moulded?
Yes. Crystal PS and SAN give a clear or tinted stand, but they show every flow mark and weld line. A polished mould, careful gate placement and dried SAN keep the visible faces clean.
How Is a Weighted Pen Stand Made?
The base gets a pocket for a metal or filled weight fitted after moulding, or a seat for an insert placed in the mould. Heft then comes from the weight, not from thick plastic that would sink.Can Pratishna Recommend a Machine for My Pen Stand?
Yes. Share the stand drawing or sample, material, part weight, mould size, the other parts in the family and your monthly quantity, and Pratishna Engineers will recommend a machine.Does the Machine Suit Other Stationery Parts Too?
Yes. Machines in this size band can also run punch and tape dispenser housings, geometry instruments, plastic rulers and clipboard fittings, subject to the mould.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]