Injection Moulding Machine for Overhead and Hand Showers
Overhead and hand showers are made on horizontal injection moulding machines from ABS, with POM, PP or PC for some inner parts. The flat face plate sets clamping force more than part weight does, followed by cavity count and mould size. Dry ABS and an even nozzle plate wall matter most, since splay scraps plated parts.
For shower parts, machine selection starts from the face plate projected area and the mould footprint, then the shot needed for the body. Pratishna Engineers supplies horizontal injection moulding machines for shower moulding and can recommend a configuration for your shower range.
Moulding Overhead Showers?
Share your face plate size, body drawing, material and finish, and Pratishna Engineers will recommend a suitable machine.
Machine Requirements for Overhead and Hand Shower Moulding
Shower parts are light but wide and often plated, which shapes the machine choice in these ways:
- Clamping force sized to the flat face plate area
- Even wall across the nozzle plate for a uniform spray
- Dryer for ABS so plated bodies come out free of splay
- Balanced gating on round face plates to limit warp
- Tie-bar spacing that takes wide overhead shower moulds
- Stable injection speed to keep flow marks out from under chrome
Recommended Machine for Overhead and Hand Showers
Hand shower bodies and small face plates fit the E Series (75-180 T). Wider overhead shower plates, which load the clamp through their flat area, move to the C Series (140-320 T). The H Series (120-350 T) suits the largest round or square overhead moulds and multi-cavity hand shower tools.
Not Sure Which Machine You Need?
Share your shower face plate and body details for a machine suggestion.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBSanitary & Bathroom Fittings Components & Machine Guide
A guide to Sanitary & Bathroom Fittings components, covering taps, bib cocks, angle cocks, health faucets, showers, cistern fittings, traps and drains. It explains PTMT, POM, ABS and UPVC, leak-free threads and seats, and how to match each part to a suitable machine.
Download PDFPDF · 203 KB
FAQs / Buyer Questions
Points shower makers raise most when they size a press.
Which Injection Moulding Machine Is Used to Make Overhead and Hand Showers?
Hand showers usually sit on the E Series, while wide overhead plates may need the C or H Series. The choice follows face plate diameter, cavity count and the mould base width between the tie-bars.Why Does a Light Shower Face Plate Need More Tonnage?
Clamping force follows projected area and cavity pressure, not part weight. A wide, thin face plate spreads melt over a large flat area, so the mould needs more clamp to stop flash at the parting line.Why Must ABS Be Dried Before Moulding Plated Showers?
ABS picks up moisture from the air. Undried resin gives splay, silver streaks on the surface, and after chrome plating those marks cannot be polished out. A hopper dryer run to the resin maker’s data avoids this.
Where Are POM, PP and PC Used in a Shower?
ABS covers the body and face plate. POM suits spray-change discs, pivots and ball joints that slide or turn. PP can serve hidden inner parts, and PC is an option for clear or tinted decorative pieces.Can Pratishna Recommend a Machine for My Overhead or Hand Shower?
Yes. Share the face plate size, body and nozzle plate drawings, material, finish, part weights, mould dimensions and cavity count, and Pratishna Engineers will recommend a suitable machine.Does the Machine Suit Other Bathroom Fittings Too?
Yes. Similar machines can mould health faucet heads, angle cocks, floor drain gratings and cistern fittings, subject to the mould size and material.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]