Injection Moulding Machine for Street Light Housing Parts and Gear Trays
Street light and outdoor luminaire housing parts and gear trays are made on horizontal injection moulding machines from UV-stabilised FR PC, glass-filled PA6 or PC/ASA. Machine size depends on part area, depth and wall thickness. Flatness of the sealing face matters most, because warpage there breaks the gasket seal and lets water in.
Outdoor parts need UV-stable material, warp control on large flat faces and steady cooling across the mould. Pratishna Engineers supplies horizontal injection moulding machines for street light housing parts and can recommend a configuration for your part and mould.
Manufacturing Street Light Parts?
Share the part drawings, materials, gasket design and volumes, and Pratishna Engineers will recommend a suitable machine.
Machine Requirements for Street Light Housing Parts
Road and area lighting parts stay outdoors for years, and the gasket face decides whether water stays out. Points to check when selecting a machine:
- UV-stabilised grade so FR PC does not yellow outdoors
- Flat, warp-free sealing faces and gasket grooves
- Balanced cooling across large housing parts and covers
- Wear-resistant screw for glass-filled PA6 gear trays
- Drying of PC, PA6 and PC/ASA before moulding
- Platen size and opening stroke for deep housing sections
Recommended Machine for Street Light Housing Parts
Gear trays, driver covers and smaller luminaire parts can run on the E Series (75-180 T). Larger housing sections and covers belong in the C Series (140-320 T) and H Series (120-350 T), near the top of the plastic size band. Mould height and tool weight are worth checking against the platen early in the quote.
Not Sure Which Machine You Need?
Share your luminaire part drawings and sizes for a recommendation.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBLighting & Electrical Components & Machine Guide
A guide to Lighting & Electrical components, covering CFL holders, tube light fixtures, potting boxes, diffusers, downlight housings, street light parts and cable glands. It explains PC and PMMA optics, heat-resistant and flame-retardant grades, and how to match each part to a suitable machine.
Download PDFPDF · 202 KB
FAQs / Buyer Questions
Questions outdoor lighting makers ask before ordering a machine.
Which Injection Moulding Machine Is Used to Make Street Light Housing Parts?
Most moulded street light parts sit in the C and H Series range, with gear trays and small covers on the E Series. The choice follows projected area, shot weight and the depth of the housing section.Why Does a Street Light Cover Turn Yellow?
Standard FR PC yellows and loses strength under sunlight without UV stabilisation. Outdoor parts use UV-stabilised PC or PC/ASA, and any masterbatch or regrind added must keep the same protection.How Is Warpage Controlled on the Sealing Face?
Even wall thickness, balanced cooling on both mould halves and gating that fills the face evenly keep it flat. Glass-filled PA6 warps along the fibre direction, so gate position is set with the gasket groove in mind.
Are Large Street Light Bodies Injection Moulded?
Smaller and mid-size housings can be moulded. The largest road lighting bodies usually go past the plastic size band and are die-cast aluminium, fitted with moulded gear trays, covers and accessories.Can Pratishna Recommend a Machine for My Street Light Parts?
Yes. Share the part drawings or samples, material grades, gasket design, part weights, mould sizes, cavity counts and monthly volume, and Pratishna Engineers will recommend suitable machines.Does the Machine Suit Other Outdoor Lighting Parts Too?
Yes. Similar machines can mould cable glands, LED potting boxes, diffuser covers and tube light gear trays, subject to each mould and material.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]