Injection Moulding Machine for Furniture Grommets
Furniture grommets are made on horizontal injection moulding machines, usually in multi-cavity moulds, from TPE, TPV or soft PVC, with PP for rigid desk grommet rings. Cavity count and the projected area of the flange decide machine size. Flash control on the soft compound is the main process point, because soft flash tears instead of trimming cleanly.
For desk and panel grommets, machine selection comes down to fine control of injection and holding pressure on soft compounds, plus platen space for multi-cavity tools. Pratishna Engineers supplies horizontal injection moulding machines for grommet production and can suggest a set-up once it sees your grommet and mould.
Manufacturing Furniture Grommets?
Share your grommet drawing, compound hardness and panel hole size, and Pratishna Engineers will suggest a machine for it.
Machine Requirements for Furniture Grommet Moulding
Soft grommets bring flash and demoulding problems that rigid parts rarely show. Points to check when selecting a machine:
- Low, finely controlled injection pressure for soft TPE
- Tight parting line and shut-off faces against soft flash
- Ejection that releases a soft, deforming part without tearing
- Barrel temperature control that avoids degrading soft PVC
- Thin flaps and cable slits filled without short shots
- Platen space for multi-cavity grommet tools
Recommended Machine for Furniture Grommets
Grommets are small and soft, so clamping force stays low even on multi-cavity moulds. The E Series (75-180 T) suits many grommet tools, with smaller moulds sized to the bottom of that range. Larger PP desk grommet rings, or high-cavity tools for wire-pass grommets, can move to the H Series (120-350 T).
Not Sure Which Machine You Need?
Share your grommet compound and cavity plan for a machine suggestion.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBFurniture & Hardware Components & Machine Guide
A guide to Furniture & Hardware components, covering chairs, stools, tables, drawers, storage, hinges, drawer channels, knobs, castors and fittings. It explains large-part moulding, mould height, POM and nylon hardware, and how to match each part to a suitable machine.
Download PDFPDF · 203 KB
FAQs / Buyer Questions
Questions furniture hardware makers raise before ordering a machine for grommets.
Which Injection Moulding Machine Is Used to Make Furniture Grommets?
An E Series machine covers small soft grommets in multi-cavity tools. Larger PP desk grommet rings, or tools with many cavities, can go to the H Series. Tonnage is confirmed from the projected area and the compound.Can Rubber Grommets Be Made on an Injection Moulding Machine?
Grommets in EPDM or NBR rubber are usually compression or transfer moulded, a different process. TPE, TPV and soft PVC give a rubber-like feel on a standard thermoplastic machine, so confirm the compound before asking for a quote.Why Does Flash Appear on Soft Grommets?
Soft compounds run into very small gaps at the parting line and vents. Worn shut-off faces, high injection pressure or a hot melt make it worse. Soft flash tears rather than breaking off, so preventing it in the mould beats trimming.
Can a Grommet Combine a Rigid Ring With a Soft Seal?
Yes, but a rigid PP ring with a soft TPE seal moulded onto it is a two-shot part, which needs a machine built to the application. Single-material soft or rigid grommets run on the standard E and H Series.Can Pratishna Recommend a Machine for My Grommet?
Yes. Share the grommet drawing or a sample, the compound and its hardness, part weight, cavities planned, mould size and monthly quantity, and Pratishna Engineers will suggest a machine.Does the Machine Suit Other Furniture Hardware Parts Too?
Yes. Similar E and H Series machines can mould fastener caps, pipe end caps, door bumpers and drawer channel components, depending on each mould.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]